SAMSUNG DC ERROR CODE: The DC error code shows on your washers display when your Samsung washer is unable to spin DUE to an unbalanced load. SAMSUNG UE ERROR CODE: The UE error code tells you that the laundry load is unbalanced and therefore cannot spin.
Simply so, what does DC error mean on Samsung washer?
Samsung front-load washer dc error code. A dc error code on your Samsung front-load washer means the washer won't spin because the load is unbalanced.
Also Know, what does Samsung washing machine mean? 1-4 of 4 Answers It means "unbalanced and retrying" so it's going to retry by adding a lot more water.
Regarding this, how do you reset a Samsung washer?
To reset your Samsung washing machine you need to simply disconnect the washing machine from power for 5 to 10 minutes. (Unplug the washer from the wall outlet or flip the breaker in the breaker box for the washing machine).
How do I troubleshoot my Samsung washer?
SAMSUNG WASHER FIX/SOLUTION:
- Check the fuse or reset the circuit breaker.
- Straighten the drain hoses.
- Eliminate kinked hoses.
- If there is a drain restriction, troubleshoot it.
- Close the door and press the Start/Pause button.
- For your safety, your washer will not tumble or spin unless the door is closed.
Similar Question and The Answer
How do you calibrate a Samsung top load washer?
Power off, and then power on the washing machine. Hold down Temp. and Delay End+ simultaneously for 3 seconds to enter Calibration mode. Press and hold Start/Pause (Hold to Start) to run the Calibration cycle. When the cycle is complete, “0” appears on the display and the washing machine will turn off automatically.
How do you fix an unbalanced washing machine?
How to Repair a Washing Machine that Is Unbalanced Step 1 - Check Level. Place a straight level on top of the washer to see how much off balance the washing machine is. Step 2 - Level with Legs. Most washing machines come with adjustable legs in the front and the back. Step 3 - Tighten Drum. Step 4 - Keep Large Items Out.
What are the codes on a Samsung washer?
Samsung Front Load Washer Fault Codes Fault Code Washer Problem LO or FL Door lock error ds Door is not locked dc Unbalanced load Sud (F70) Too many suds
Where is the MEMS sensor on a Samsung washer?
Answer Aaron, the mems sensor would be accessed by removing the top panel of the washer. The wires can be checked for continuity and repaired as necessary. Answer Carol, the mems sensor is going to be located at the top of the tub assembly near the front.
How do I fix my Samsung Washer error code 3e?
How To Fix 3E Samsung Washer Error Code: Unplug The Washing Machine: Unplug the washer for 2-3 minutes. Check Wire Connections On Drive Motor: One fairly common issue that causes the 3E error code is connection problems. Check Wire Connections On Control Board: Check Hall Sensor:
Why is my Samsung washing machine flashing?
Your appliance will display a UE code when it has detected an unbalanced load and has stopped the spin for safety reasons. With any washing machine, it is vital to ensure that the load is evenly balanced when using a spin cycle. Redistribute washing by adding or removing items to ensure a more balanced load.
Why does my Samsung Washer not spin?
To determine if the drive motor is defective, first ensure that the motor is getting power. If the drive motor hums but doesn't run, is noisy, or does not turn freely, replace it. The washer transmission might be worn out or defective. Transmissions have gears in them that can fail causing the washer to not spin.
Is there a fuse inside a washing machine?
Washing machines have fuses that protect them from power surges. Washing machines require lots of power to run. The other fuse sits in the lid switch on some machines; if the washer overheats or there is a power surge, the washer will not run again until the fuse in the switch is replaced.
Why did my washer just stop working?
If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine's spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn't work, the belt may be loose or broken.